**Outdoor Intelligent PIR+MV Motion Detector
1.General Introduction On Outdoor Application
This detector is remarkable in function, but the following notices can make itmore
stable if installer can pay attention to them:
Direct or reflective sun light is no good for detector operation, try to avoid them during installation. Our outdoor
PIR adopts double-layered screen light sensing system, which is very effective for screeing of interfering light.
SUNSHINE
High weeds and shrubbery in detection range may wave in wind and cause false alarm, especially for those detectors
operating in horizontal fan area, so keep cutting on weeds and shrubbery.
WEEDS
Sudden rainstorm can cool the hot pitch road or surface of other roads quickly. And all detectors can detect rain
in the sky, but detector with down view window can even detect water on ground, which will bring much more
interference to detectors outdoor than that mounted on wall, so everything will lower its temperature similar to water,
human body or cars after pouring from rain can offer very little temperature gap for detection, so sensitivity will
be lowered a lot.
RAIN
Insects will trigger false alarm when they climb into detector or stay on lens, while those staying away from
detectors can't trigger alarm. If there is interference from insects, please re-install detector or use insecticide.
And please adopts strictly sealed components on those drilled holes or glass glue around detector.
INSECTS
Moving car in detection range may trigger false alarm to detector.
CAR
Detector is sensitive to change from temperature difference in detection area, if target temperature is very close to
previous environment temperature, there will be no temperature change, detector sensitivity will be lowered and
will not be triggered sometimes when there is intrusion.
INSUFFICUENT TEMPERATURE DIFFERENCE
Lens becomes easily dirty when used outdoor, so please check the lens from time to time in order to avoid alarm
miss caused by low sensitivity from dirty lens.
DIRT ON LENS
Detector will trigger false alarm easily if installation base can be interfered by vibration, this is the reason why
some detectors installed near to street can cause false alarm easily
2.DISCLAIMER
I. Product limitation
This wireless detector is a highly qualified product worthy of trust, but below situations might appear in radio transmission and certification limitation (FCC or other principles):
A. Whatever code is selected, control panel may be blocked caused by interference from radio signal or wave in similar frequencies.
B. Control panel can only receive an alarm signal from 1 detector in 1 time.
C. Make regular tests on radio devices in order to confirm interference is not from them and guarantee its stability
II. Frequencies distribution in Europe
315MHz Limited in all EU members
433.92MHz No limitation in EU members
III. Standards
This device is certified with 1999/5/EC standards and index on radio and telecom terminal devices, 315MHz
the module is certified with 15 part of FCC standard, operation must follow below conditions:
868.95MHz Allowed in all EU members
869.2625MHz No limitation for all EU
(1)This device should not organize harmful interference.
(2)This device must obey any interference source, including those may cause improper operation. Operator should not
change the product at random, manufacturer not suggest or allow user to make modification on product except for those operation approved by FCC. Digital circuit of this product has passed test lab's test and follow B grade digital
instruments standard; it is coherent with article 15 of FCC, these limitations offer protection to no interference
from family devices. This device mainly produce radio transmission power, improper installation may cause nocuous
interference to TV or other radio devices. And also, there is no guaranty of nocuous RF interference after each installation.
If device cause interference, can be recognized by switch on/off, user can lower interference by following steps:
- Re-adjust or place position of antenna on receiver
- Enlarge distance between transmitter and receiver
-Turn to professional people or sellers.
3.Introduction on Products
This is a digital wireless motion detector with remarkable functions, it can avoid outdoor interference from sunshine,
UV & RF, head light on car etc and is highly effective for water/dust/insects/ wind proof. It is matched with follow advanced
technology: direct calculation and analysis technology from intelligent high-speed microchip to intrusion infrared signal,
double polarity test technology, automatic temperature compensation technology, direct adjustment technology to
sensitivity on digital signal, filtering technology from multi-layer infrared channels to mixed light. Its particular
calculation on pets chargeable data can avoid false alarm caused by 20kg small animals effectively. At the same
time, it is also outstanding in anti hot air, waving curtains etc, can offer forced test on the base of 2-grade sensitivities.
Its unique low-power-consumption solution can offer a guaranty of 24 months' factory battery life expectancy. In
a word, this detector is advanced and stable enough to offer best security Protection indoor and outdoor with its
IP65 water proof structure.
4.Main Function
-Super mini power-consumption solution
-2 grade sensitivities for option
-Digital pet immunity up to 20kg
-Bi-directional temperature compensation
-EDS/electric shock proof/mobile interference proof
-Anti white light
-Fully sealed optical parts
-Multi-direction bracket fit for corner/wall/ceiling mount
5.Technical Parameter
Power : 9-16VDC
Current : 30mA
Mount height : 1.8m-2.4m
Detection range :12m*12m 100°
Sensitivity :
Anti EMI :0.1-500MHz/30V/m
Anti white light :>10000 LUX
Alarm time : 3s
Operation temperature :-10℃/+55℃
Operation humidity :95% RH
Detection speed :0.2-3.5 m/s
Fire proof : ABS plastic
Pet immunity : 20kg
Size :148*75*54mm
6. INSTALLATION GUIDE
Select most suitable installation point fit for PIR detection, put detector onto proper position, keep away
from door, window, running machine or heat source.
7.Installation & Bracket
Wall Mounting:
Use a cross-type screw driver to loose screw at
bottom of housing and open covers as figure, and
then move down PCB unit, then installation can
be ready to start.
Loose PCB unit screw as figure, press down the
buckles with 2 fingers, PCB unit can be taken down.
Then detector can be installed according to actual
needs.
In order to get best signal coverage, detector must
be installed at the height of 2.1m vertically. Make
sure that there is no obstacle in front of detector,
detection angle is wide. Make decision on which
installation way according to actual needs, and
then make a mark on needed holes on wall, drill
4 holes with 6mm diameter, insert relevant 4
rubber stoppers into the holes, then detector can
be fasten onto the wall by screws.
Loose PCB unit screw as figure, press down the
buckles with 2 fingers, PCB unit can be taken down.
Then detector can be installed according to actual needs.
9. Walking Test & Setting
MW
Tune microwave tuner to minimum, capacity can be adjusted
from 2-15m to the extremity of protection area when LED
indicator turns off operation radial movement to the detector,
check MW detection by green LED. If green LED doesn't light,
turn the MW tuner in clock wise to increase its capacity; repeat
this tests for several times till you get the required distance.
Remarks: MW adjustment turn the capacity to the minimum,
for MWcan penetrate wall while over high capacity is not helpful
for detector function in its protection area. MW gets highest
sensitivity when it performs radial movement to detectors
PIR
Close the front cover, when LED indicator turns off, perform
horizontal movement in the detection area, check the detection
status of PIR through the yellow LED. This step can check
whether there is deal corner in the detection area; when PIR
gets highestsensitivity when horizontal movement to detector.
When all DIP switches are in “OFF” status, monitor is in
standard operation.
When jumper is set to LOW, sensitivity of two sensors is low
When jumper is set to OFF, even if detector is triggered,
LED will not light just for the purpose of invisibility
(Recommended)
PIR During the time, signals detected by both negative and
positive period of PIR are limited.
MW the detection response speed of MW is 0.5 seconds
running speed is 0.6m/second.
Sensitivity & LED Setting
10. WIRE UP THE TERMINAL
The contact is closed normally, if remove the
frontsmall cover or the whole detector from
the wall, contact will open. (sensor connects
with wall in lay style monitor)
11.Vertical adjustment
Detector can get its best detection by setting of PCB
vertical height, strongly suggest installer should make
optimum setting to PCB vertical height according to actual
environment
12.Pet immunity
Pet immunity is a high index for judgment of PIR detector function, we adopt 2 methods on pet
Immunity process at the same time:
1.Physical method: special process of Fresnel lens detection area to lower false alarm rate caused
by small animals
2.Software analysis method: analysis on technical data on detector signal and make comparison
with data base in the microchip in detector, then draw a conclusion on moving object to verify
it is human being or pets.
From above we can know that function of pet immunity is relevant, this relativity includes 2 parts: firstly, pet immunity
is relevant, but its false alarm rate is greatly lowered comparing detectors without pet immunity function, at the same
time, there is limitation on pets' quantity and size. Secondly, installation is very important to pet immunity, it is with
some requirements, not a random installation can reach a good result, so please read details in the manual before installation.
**Outdoor Intelligent PIR+MV Motion Detector
1.General Introduction On Outdoor Application
This detector is remarkable in function, but the following notices can make itmore
stable if installer can pay attention to them:
Direct or reflective sun light is no good for detector operation, try to avoid them during installation. Our outdoor
PIR adopts double-layered screen light sensing system, which is very effective for screeing of interfering light.
SUNSHINE
High weeds and shrubbery in detection range may wave in wind and cause false alarm, especially for those detectors
operating in horizontal fan area, so keep cutting on weeds and shrubbery.
WEEDS
Sudden rainstorm can cool the hot pitch road or surface of other roads quickly. And all detectors can detect rain
in the sky, but detector with down view window can even detect water on ground, which will bring much more
interference to detectors outdoor than that mounted on wall, so everything will lower its temperature similar to water,
human body or cars after pouring from rain can offer very little temperature gap for detection, so sensitivity will
be lowered a lot.
RAIN
Insects will trigger false alarm when they climb into detector or stay on lens, while those staying away from
detectors can't trigger alarm. If there is interference from insects, please re-install detector or use insecticide.
And please adopts strictly sealed components on those drilled holes or glass glue around detector.
INSECTS
Moving car in detection range may trigger false alarm to detector.
CAR
Detector is sensitive to change from temperature difference in detection area, if target temperature is very close to
previous environment temperature, there will be no temperature change, detector sensitivity will be lowered and
will not be triggered sometimes when there is intrusion.
INSUFFICUENT TEMPERATURE DIFFERENCE
Lens becomes easily dirty when used outdoor, so please check the lens from time to time in order to avoid alarm
miss caused by low sensitivity from dirty lens.
DIRT ON LENS
Detector will trigger false alarm easily if installation base can be interfered by vibration, this is the reason why
some detectors installed near to street can cause false alarm easily
2.DISCLAIMER
I. Product limitation
This wireless detector is a highly qualified product worthy of trust, but below situations might appear in radio transmission and certification limitation (FCC or other principles):
A. Whatever code is selected, control panel may be blocked caused by interference from radio signal or wave in similar frequencies.
B. Control panel can only receive an alarm signal from 1 detector in 1 time.
C. Make regular tests on radio devices in order to confirm interference is not from them and guarantee its stability
II. Frequencies distribution in Europe
315MHz Limited in all EU members
433.92MHz No limitation in EU members
III. Standards
This device is certified with 1999/5/EC standards and index on radio and telecom terminal devices, 315MHz
the module is certified with 15 part of FCC standard, operation must follow below conditions:
868.95MHz Allowed in all EU members
869.2625MHz No limitation for all EU
(1)This device should not organize harmful interference.
(2)This device must obey any interference source, including those may cause improper operation. Operator should not
change the product at random, manufacturer not suggest or allow user to make modification on product except for those operation approved by FCC. Digital circuit of this product has passed test lab's test and follow B grade digital
instruments standard; it is coherent with article 15 of FCC, these limitations offer protection to no interference
from family devices. This device mainly produce radio transmission power, improper installation may cause nocuous
interference to TV or other radio devices. And also, there is no guaranty of nocuous RF interference after each installation.
If device cause interference, can be recognized by switch on/off, user can lower interference by following steps:
- Re-adjust or place position of antenna on receiver
- Enlarge distance between transmitter and receiver
-Turn to professional people or sellers.
3.Introduction on Products
This is a digital wireless motion detector with remarkable functions, it can avoid outdoor interference from sunshine,
UV & RF, head light on car etc and is highly effective for water/dust/insects/ wind proof. It is matched with follow advanced
technology: direct calculation and analysis technology from intelligent high-speed microchip to intrusion infrared signal,
double polarity test technology, automatic temperature compensation technology, direct adjustment technology to
sensitivity on digital signal, filtering technology from multi-layer infrared channels to mixed light. Its particular
calculation on pets chargeable data can avoid false alarm caused by 20kg small animals effectively. At the same
time, it is also outstanding in anti hot air, waving curtains etc, can offer forced test on the base of 2-grade sensitivities.
Its unique low-power-consumption solution can offer a guaranty of 24 months' factory battery life expectancy. In
a word, this detector is advanced and stable enough to offer best security Protection indoor and outdoor with its
IP65 water proof structure.
4.Main Function
-Super mini power-consumption solution
-2 grade sensitivities for option
-Digital pet immunity up to 20kg
-Bi-directional temperature compensation
-EDS/electric shock proof/mobile interference proof
-Anti white light
-Fully sealed optical parts
-Multi-direction bracket fit for corner/wall/ceiling mount
5.Technical Parameter
Power : 9-16VDC
Current : 30mA
Mount height : 1.8m-2.4m
Detection range :12m*12m 100°
Sensitivity :
Anti EMI :0.1-500MHz/30V/m
Anti white light :>10000 LUX
Alarm time : 3s
Operation temperature :-10℃/+55℃
Operation humidity :95% RH
Detection speed :0.2-3.5 m/s
Fire proof : ABS plastic
Pet immunity : 20kg
Size :148*75*54mm
6. INSTALLATION GUIDE
Select most suitable installation point fit for PIR detection, put detector onto proper position, keep away
from door, window, running machine or heat source.
7.Installation & Bracket
Wall Mounting:
Use a cross-type screw driver to loose screw at
bottom of housing and open covers as figure, and
then move down PCB unit, then installation can
be ready to start.
Loose PCB unit screw as figure, press down the
buckles with 2 fingers, PCB unit can be taken down.
Then detector can be installed according to actual
needs.
In order to get best signal coverage, detector must
be installed at the height of 2.1m vertically. Make
sure that there is no obstacle in front of detector,
detection angle is wide. Make decision on which
installation way according to actual needs, and
then make a mark on needed holes on wall, drill
4 holes with 6mm diameter, insert relevant 4
rubber stoppers into the holes, then detector can
be fasten onto the wall by screws.
Loose PCB unit screw as figure, press down the
buckles with 2 fingers, PCB unit can be taken down.
Then detector can be installed according to actual needs.
9. Walking Test & Setting
MW
Tune microwave tuner to minimum, capacity can be adjusted
from 2-15m to the extremity of protection area when LED
indicator turns off operation radial movement to the detector,
check MW detection by green LED. If green LED doesn't light,
turn the MW tuner in clock wise to increase its capacity; repeat
this tests for several times till you get the required distance.
Remarks: MW adjustment turn the capacity to the minimum,
for MWcan penetrate wall while over high capacity is not helpful
for detector function in its protection area. MW gets highest
sensitivity when it performs radial movement to detectors
PIR
Close the front cover, when LED indicator turns off, perform
horizontal movement in the detection area, check the detection
status of PIR through the yellow LED. This step can check
whether there is deal corner in the detection area; when PIR
gets highestsensitivity when horizontal movement to detector.
When all DIP switches are in “OFF” status, monitor is in
standard operation.
When jumper is set to LOW, sensitivity of two sensors is low
When jumper is set to OFF, even if detector is triggered,
LED will not light just for the purpose of invisibility
(Recommended)
PIR During the time, signals detected by both negative and
positive period of PIR are limited.
MW the detection response speed of MW is 0.5 seconds
running speed is 0.6m/second.
Sensitivity & LED Setting
10. WIRE UP THE TERMINAL
The contact is closed normally, if remove the
frontsmall cover or the whole detector from
the wall, contact will open. (sensor connects
with wall in lay style monitor)
11.Vertical adjustment
Detector can get its best detection by setting of PCB
vertical height, strongly suggest installer should make
optimum setting to PCB vertical height according to actual
environment
12.Pet immunity
Pet immunity is a high index for judgment of PIR detector function, we adopt 2 methods on pet
Immunity process at the same time:
1.Physical method: special process of Fresnel lens detection area to lower false alarm rate caused
by small animals
2.Software analysis method: analysis on technical data on detector signal and make comparison
with data base in the microchip in detector, then draw a conclusion on moving object to verify
it is human being or pets.
From above we can know that function of pet immunity is relevant, this relativity includes 2 parts: firstly, pet immunity
is relevant, but its false alarm rate is greatly lowered comparing detectors without pet immunity function, at the same
time, there is limitation on pets' quantity and size. Secondly, installation is very important to pet immunity, it is with
some requirements, not a random installation can reach a good result, so please read details in the manual before installation.
